s i da45 e series 50w desktop power supply for industrial equipment C wide input voltage 90 to 264 vac, 47 to 63hz C iec - 320 - c14 input inlet C output voltage available from 2vdc thru 50vdc C input surge current, over voltage and overload protection C operating temperature - 20~70c C single to triple output C class i insulation 2 year warranty approvals: single output part number output voltage max. output current total regulation max output power s i da45 e - s00 0 2 ~ 0 3 vdc 8.00 a max 7% 24w s i da45 e - s01 03 ~ 05 vdc 8.00 a max 5% 40w s i da45 e - s02 05 ~ 06 vdc 8.00 ~ 6.66 a 5% 40w s i da45 e - s03 06 ~ 08 vdc 7.00 ~ 5.25 a 5% 42w s i da45 e - s04 08 ~ 11 vdc 5.63 ~ 4.00 a 4% 45w s i da45 e - s05 11 ~ 13 vdc 4.00 ~ 3.46 a 3% 45w s i da45 e - s06 13 ~ 16 vdc 3.46 ~ 2.81 a 3% 45w s i da45 e - s07 16 ~ 21 vdc 3.12 ~ 2.38 a 3% 50w s i da45 e - s08 21 ~ 27 vdc 2.30 ~ 1.85 a 2% 50w s i da45 e - s09 27 ~ 33 vdc 1.85 ~ 1.51 a 2% 50w s i da45 e - s10 33 ~ 40 vdc 1.51 ~ 1.25 a 2% 50w s i da45 e - s11 40 ~ 50 vdc 1.25 ~ 1.00 a 2% 50w multi output model number output 1 output 2 output 3 max output power vonom iomin iomax regmax vonom iomin iomax regmax vonom iomin iomax regmax s t da45 e - d 00 +3.3v 0.5a 5a 7% +12v 0.3a 2a 5% 40w s t da45 e - d01 +5v 0.5a 5a 5% +12v 0.3a 2a 5% 42w s t da45 e - d02 +5v 0.8a 5a 7% +15v 0.3a 1.5a 5% 42w s t da45 e - d03 +5v 0.5a 5a 5% +24v 0.1a 1a 5% 42w s t da45 e - d04 +3.3v 0.5a 5a 7% +5v 0.2a 2a 5% 26.5w s t da45 e - d09 +12v 0.3a 3a 5% - 12v 0.1a 1a 5% 42w s t da45 e - d10 +15v 0.2a 2a 5% - 15v 0.1a 1a 5% 42w s t da45 e - d15 +5v 0.5a 5a 5% - 24v 0.1a 1a 5% 42w s t da45 e - d16 +5.1v 0a 1a 5% +7.2v 0.2a 2.6a 5% 23.82w s t da45 e - t 00 +3.3v 1.0a 5a 7% +12v 0.3a 2a 5% - 12v 0.1a 0.8a 5% 42w s t da45 e - t01 +5v 0.5a 5a 5% +12v 0.2a 2a 5% - 5v 0a 0.8a 5% 42w s t da45 e - t02 +5v 0.5a 5a 5% +12v 0.2a 2a 5% - 12v 0a 0.8a 5% 42w s t da45 e - t03 +5v 0.5a 5a 5% +15v 0.3a 2a 6% - 15v 0a 0.8a 5% 42w s t da45 e - t04 +5v 0.5a 5a 5% +24v 0.2a 1a 5% - 24v 0a 0.5a 5% 42w s t da45 e - t05 +5v 0.5a 5a 5% +24v 0.1a 1a 5% - 12v 0a 0.8a 5% 42w s t da45 e - t06 +3.3v 0.5a 5a 7% +12v 0.4a 2a 5% - 5v 0a 0.8a 5% 42w stda45 e - s0 0 , s01 ,d15, d16,t00, t05,t06 is not approved by tuv - pse conditions parameter test conditions min. typ. max. unit operating temperature - 20 40 70 c storage temperature - 40 85 c relative humidity 5 95 % operating temperature at 25c, calculated per mil - hdbk - 217f 0.1 m hrs de - rate linearly from 100% load at 40c to 50% load at 70c
electrical characteristics parameter test conditions min. typ. max. unit input voltage operating voltage 90 264 vac input frequency 47 63 hz output power range vin=90 to 264vac 0 50 w input current (low line) io=full load, vin=115vac 1.35 a input current (high line) io=full load, vin=230vac 0. 7 a low line inrush current io=full load, 25c, cool start, vin=115vac 12 15 a high line inrush current io=full load, 25c, cool start, vin=230vac 26 30 a efficiency io=full load, vin=230vac 7 0 75 8 0 % line regulation io=full load 0.5 1 % load regulation vin=230vac 3 15 % over voltage protection 112 132 % over current protection 110 150 % transient response io=full load to half load, vin=100vac 4 ms hold - up time io=full load, vin=110vac 1 0 ms start up time io=full load, vin=100vac 0.3 1 2 s * ripple & noise (peak to peak) full load, vin=90vac 0.5 1 % safety ground leakage current io=full load, vin=240vac 0.5 0.75 ma temperature coefficient all output - 0.04 0.04 %/c * the ripple & noise which is under 3.3vdc at 2% max approvals and compliance parameter test conditions min. unit dielectric withstanding voltage for primary to secondary primary to secondary 4242 vdc dielectric withstanding voltage for primary to ground primary to ground (not applicable for class ii) 2121 vdc isolation resistance test voltage = 500vdc 50 m emi requirements for cispr - 22 vin=220vac b class emi requirements for fcc part - 15 vin=110vac b class mechanical note: 1. dimensions are shown in inches or mm. 2. weight: 535 - 560gs approx. 3. optional output connector .
|
